This curbs runaway growth while still allowing substantial
spikes in block weight
Original specification from ArticMine:
here is the scaling proposal
Define: LongTermBlockWeight
Before fork:
LongTermBlockWeight = BlockWeight
At or after fork:
LongTermBlockWeight = min(BlockWeight, 1.4*LongTermEffectiveMedianBlockWeight)
Note: To avoid possible consensus issues over rounding the LongTermBlockWeight for a given block should be calculated to the nearest byte, and stored as a integer in the block itself. The stored LongTermBlockWeight is then used for future calculations of the LongTermEffectiveMedianBlockWeight and not recalculated each time.
Define: LongTermEffectiveMedianBlockWeight
LongTermEffectiveMedianBlockWeight = max(300000, MedianOverPrevious100000Blocks(LongTermBlockWeight))
Change Definition of EffectiveMedianBlockWeight
From (current definition)
EffectiveMedianBlockWeight = max(300000, MedianOverPrevious100Blocks(BlockWeight))
To (proposed definition)
EffectiveMedianBlockWeight = min(max(300000, MedianOverPrevious100Blocks(BlockWeight)), 50*LongTermEffectiveMedianBlockWeight)
Notes:
1) There are no other changes to the existing penalty formula, median calculation, fees etc.
2) There is the requirement to store the LongTermBlockWeight of a block unencrypted in the block itself. This is to avoid possible consensus issues over rounding and also to prevent the calculations from becoming unwieldy as we move away from the fork.
3) When the EffectiveMedianBlockWeight cap is reached it is still possible to mine blocks up to 2x the EffectiveMedianBlockWeight by paying the corresponding penalty.
Note: the long term block weight is stored in the database, but not in the actual block itself,
since it requires recalculating anyway for verification.
The blockchain prunes seven eighths of prunable tx data.
This saves about two thirds of the blockchain size, while
keeping the node useful as a sync source for an eighth
of the blockchain.
No other data is currently pruned.
There are three ways to prune a blockchain:
- run monerod with --prune-blockchain
- run "prune_blockchain" in the monerod console
- run the monero-blockchain-prune utility
The first two will prune in place. Due to how LMDB works, this
will not reduce the blockchain size on disk. Instead, it will
mark parts of the file as free, so that future data will use
that free space, causing the file to not grow until free space
grows scarce.
The third way will create a second database, a pruned copy of
the original one. Since this is a new file, this one will be
smaller than the original one.
Once the database is pruned, it will stay pruned as it syncs.
That is, there is no need to use --prune-blockchain again, etc.
get_output_key method is commonly used when working with txs and their key images. Because the method is not const, passing blockchain object though const& or pointers to const is not possible in this context. This is especially problematic in external projects (e.g., projects in moneroexamples) that use monero C++ api to operate on the blockchain and txs.
Thus, having get_output_key method will simplify moving blockchain object around through const references and pointers to const objects.
6644b9b blockchain_db: remove a couple unused functions (moneromooo-monero)
ce594f5 blockchain_db: allocate known size vector only once (moneromooo-monero)
8332698 db_lmdb: inline check_open, it's trivial and called everywhere (moneromooo-monero)
5511563 db_lmdb: avoid pointless division (moneromooo-monero)
d1efe3d cryptonote: set tx hash on newly parsed txes when known (moneromooo-monero)
9cc68a2 tx_pool: add a few std::move where it can make a difference (moneromooo-monero)
Only for pre rct for obvious reasons.
Note: DO NOT use a known spent list which includes outputs
which are not known spent. If the list includes any output
that's just strongly thought to be spent, but not provably
so, you risk finding yourself unable to sync past the point
where that output is spent.
I estimate only 200 MB saved on current mainnet though,
unless the new blackballing rule unearths a good amount of
large-amount-set extra spent outs.
This gets rid of the temporary precalc cache.
Also make the RPC able to send data back in binary or JSON,
since there can be a lot of data
This bumps the LMDB database format to v3, with migration.
on_generateblocks RPC call combines functionality from the on_getblocktemplate and on_submitblock RPC calls to allow rapid block creation. Difficulty is set permanently to 1 for regtest.
Makes use of FAKECHAIN network type, but takes hard fork heights from mainchain
Default reserve_size in generate_blocks RPC call is now 1. If it is 0, the following error occurs 'Failed to calculate offset for'.
Queries hard fork heights info of other network types
This patch allows to filter out sensitive information for queries that rely on the pool state, when running in restricted mode.
This filtering is only applied to data sent back to RPC queries. Results of inline commands typed locally in the daemon are not affected.
In practice, when running with `--restricted-rpc`:
* get_transaction_pool will list relayed transactions with the fields "last relayed time" and "received time" set to zero.
* get_transaction_pool will not list transaction that have do_not_relay set to true, and will not list key images that are used only for such transactions
* get_transaction_pool_hashes.bin will not list such transaction
* get_transaction_pool_stats will not count such transactions in any of the aggregated values that are computed
The implementation does not make filtering the default, so developers should be mindful of this if they add new RPC functionality.
Fixes#2590.
And optimize import startup:
Remember start_height position during initial count_blocks pass
to avoid having to reread entire file again to arrive at start_height
If monerod is started with default sync mode, set it to SAFE after
synchronization completes. Set it back to FAST if synchronization
restarts (e.g. because another peer has a longer blockchain).
If monerod is started with an explicit sync mode, none of this
automation takes effect.
When scanning for outputs used in a set of incoming blocks,
we expect that some of the inputs in their transactions will
not be found in the blockchain, as they could be in previous
blocks in that set. Those outputs will be scanned there at
a later point. In this case, we add a flag to control wehther
an output not being found is expected or not.
3ff54bdd Check for correct thread before ending batch transaction (Howard Chu)
eaf8470b Must wait for previous batch to finish before starting new one (Howard Chu)
c903c554 Don't cache block height, always get from DB (Howard Chu)
eb1fb601 Tweak default db-sync-mode to fast:async:1 (Howard Chu)
0693cff9 Use batch transactions when syncing (Howard Chu)
binaryFate
moneromooo-monero
Riccardo Spagni
moneroexamples
luigi1111
victorsintnicolaas
stoffu
Howard Chu
xmr-eric